mylogo

A few decades ago, all the hammers were remarkably similar to each other. Their hilt was wooden, and their heads were often very unreliable. Only the sizes of the tools differed. Now, manufacturers of hammers go to all sorts of tricks to win the attention of the consumer. Tools with a metal handle appear, and now almost all of them are supplied with a rubberized coating. In today's article we tried to mention the best hammers in a variety of classes. You are waiting and locksmith, and nail catchers, and real sledgehammers. All selected models are similar in one thing - their purchase is not disappointing.

 

 

1

Hammer which company to choose

Logic dictates that it is easiest for ax ax manufacturers to create high-quality hammers. However, they are engaged in this business quite rarely.

Most of all similar tools are produced by those companies that are familiar to us by pliers and wrenches. They have access to a large amount of tool steel, which is the most important component of any hammer.

It is curious that domestic producers of hammers feel very well. Their products are completely different from what went off the assembly lines during Soviet times. Now these tools can be trusted without doubting their capabilities.

The most popular hammers in our country are products of the following manufacturers:

1. Fit

2. MATRIX

3. SANTOOL

4. STAYER

5. STURM

But this in no way means that quality products are made only by the five companies mentioned above.

Top Sledge

KAPRIOL 12301

KAPRIOL 12301.jpg11

Recently, even sledgehammers began to be equipped with a fiberglass handle. Such a coating will not allow the tool to slip out of the hands even with an excessively active backswing. If we talk specifically about KAPRIOL 12301, then it should be noted not only the material of the handle, but also the optimal weight of the sledge hammer, which is 3 kg. Also successful work contributes to the 90-centimeter length.

The tool received a square-shaped bob. It keeps cool on the handle - it’s not worth waiting for trouble with such a sledgehammer. Most stores provide a warranty period of 6 months. You can regret only about the high cost of the tool - products with a wooden handle have a lower price tag, and therefore their popularity is higher.

Advantages:

  • Reliable square punch;
  • Applied fiberglass handle;
  • Weight will appeal to most buyers;
  • The optimal length.

Disadvantages:

  • Not everyone will want to spend that kind of money.

FIT 45232

FIT 45232.jpg1

Tools under the FIT brand often have a yellow-black handle at their disposal. FIT 45232 is no exception. This sledgehammer turned out quite long and heavy. More specifically, the weight is 4 kg. This allows you to break through any brick wall with a swing! Importantly, the handle here is made of metal - it is impossible to break it, unless the tool falls under the tank tracks.

The hammer in the sledgehammer, as it should be, has a square shape. It is made of pressed and heat-treated steel. The upper part of the handle is fiberglass. Hands will hold on to the part that has a rubber coating. Accidentally slip the tool just can not, no matter how you tried. And the manufacturer tried to reduce the price tag. And even though a sledgehammer can not be called a budget, it is cheaper than many competitors with a similar coating of the handle.

Advantages:

  • Very heavy weight;
  • There is a fiberglass and rubber coating;
  • Can serve almost forever;
  • Wow, well done.

Disadvantages:

  • Some people seem too heavy.

Top Hammers

Inforce 59035

Inforce 59035

Usually hammers with a well-thought-out design are quite expensive. But Inforce 59035 can be bought for very little money. Partly because of this, buyers leave completely positive feedback.

Although it should be noted that the tool really succeeded. It has a 500 gram mass, and its handle has a fiberglass coating. Moreover, there are finger holes on it! All this definitely will not let the hammer slip during operation. Also, it will not let you get tired - you will perform the minimum number of actions.

A pleasant bonus is the presence at the end of the handle through the hole - this allows you to hang the tool on the hook. As for the striker, it has a traditional shape, and its hardness is 10% more than what is required by DIN. It is attached to the handle by the method of injection gluing with epoxy resin. And if you still remember the heat treatment of the hammer, then there is no doubt that the hammer will serve for an arbitrarily long time.

Advantages:

  • Epoxy resin was used for bonding;
  • The rubberized handle was made of fiberglass;
  • There are protrusions under the fingers;
  • The surface of the striker was heat treated;
  • The lower part of the handle has an extension;
  • There is a hole for hanging;
  • Adequate cost.

Disadvantages:

  • Weight for some work will not be enough.

Case Technology 315100 DT / 24/6

Delo Techniki315100

A great hammer for those who need a heavier tool. Product weight is exactly one kilogram. This allows you to quickly drive even a very large nail. His striker has a traditional combined form. It is made of steel 45. The handle here is also fiberglass. The rubberized construction not only prevents the instrument from slipping, but also reduces vibrations.

The length of the product is 370 mm. At the end of the handle there is a well-defined hole that simplifies tool storage. In general, the hammer Case Technology 315100 has no serious flaws, especially if we recall its low cost. Only the lack of grooves for the fingers, which one of the competitors can boast, is capable of confusing.

Advantages:

  • Sold at a low price;
  • There is a hole on the handle;
  • Boeque was made of steel 45;
  • Very robust design;
  • Fiberglass handle securely fixed in the palm of your hand;
  • Killer kilogram weight.

Disadvantages:

  • None.

The best masons hammers

BISON MASTER 2015-05_z01

Zubr Master 2015 05 z01

The Russian manufacturer affectionately calls his creation a pickaxe. This is explained by the fact that the tool is not a full-fledged pickax yet - it affects 500-gram weight. However, he will still become an indispensable assistant of any mason. The product is useful in various construction works, and it can serve for a very long time - the manufacturer assures that the firing pin here has increased durability. Some questions are caused only by the handle made of wood.

Tool steel 55 was used for the production of the striker. It is difficult to say what is missing here. It is possible that someone may find the absence of a hole strange, which is why the hammer will have to be stored in the tool box.

Advantages:

  • The head is made of tool steel grade 55;
  • Countertops are hardened;
  • Relatively low price.

Disadvantages:

  • The wooden handle does not inspire confidence;
  • There is no hole on the handle.

Sturm 1010-05-600

Sturm 1010 05 600

This hammer of the bricklayer may seem very small. But first of all you should pay attention to weight. And here it is 600 grams. This is quite enough for percussion with stone, brick or concrete. The double-sided striker was made of solid steel, but the manufacturer decided not to name its brand.Nevertheless, buyers note the resistance of the striker to almost any load.

The handle of this tool is a two-component. Its basis can be considered steel, which flows smoothly into the firing pin. On top of it is a fiberglass mass, which has three notches - fingers are conveniently put on them. All this contributes to the fact that during operation the hand does not slip at all.

Advantages:

  • Long service life;
  • Not afraid of serious loads;
  • Fiberglass has recesses for fingers;
  • The hand does not slip at all;
  • The end of the handle is intentionally extended;
  • The optimum weight for such a hammer.

Disadvantages:

  • The price may seem slightly overpriced.

The best inertia hammer

SANTOOL 030833-675

SANTOOL 030833 675

This type of hammer is also called recoilless. In the people, such an instrument is called a mallet. All such hammers are very similar to each other, their design is verified over the years. Specifically, SANTOOL 030833-675 has a 320 mm length. At the end of the handle here, there is a thickening that can serve as a stand. Boek also has a 50-millimeter diameter, which is enough in most cases.

Advantages:

  • Optimal length;
  • Reliable and verified design;
  • Decent striker diameter;
  • Weight is 680 grams.

Disadvantages:

  • May seem expensive.

Best Straightening Hammer

Unipro 16148U

Unipro 16148U

Sometimes a hammer is not required to drive a nail or break a wall. In some cases, this tool needs to handle damage over a large area. In particular, body repair is carried out with a special hammer.

Such a tool is called leveling. If you are looking for it, then take a look at Unipro 16148U. This hammer comes with two nozzles. One is made of rubber, and the second is made of elastic polymer. This allows you to choose a nozzle for a specific surface.

The basis of the hammer was created from steel, for greater beauty it is polished. On the handle there is a rubber coating that does not give palm slips even if it sweats. Product weight is 500 grams - this is the best option for leveling hammer.

Advantages:

  • Nice appearance;
  • Two replaceable nozzles in a set;
  • Very high reliability;
  • There is a rubber coating on the handle;
  • Weight ideal for such a tool;
  • The price should please everyone.

Disadvantages:

  • None.

Top Roof Hammers

Bahco 485

Bahco 485

When repairing the roof and solving other similar problems, you will definitely need a hammer, complete with a nail puller. Bahco 485 will be a good roofer choice. This tool seems both simple and beautiful. They use a steel handle, over which a rubber pad is put on. The hammer does not slip at all in the hand, even though there are no holes for the fingers here. It should be noted that the inside of the handle is hollow, so the instrument weighs only slightly more than 600 grams, and this despite the 308 mm length.

Work as a roofer will be carried out with the help of steel striker. On one side there is a square impact part. Whether it is hardened is not reported. But looking at the price tag, in this matter you cease to doubt. On the other side of the striker there is a nail puller. A nice addition is the magnetic holder - a rare visitor in hammers.

Advantages:

  • Very robust design;
  • There is a rubber pad on the metal handle;
  • There is a nail puller;
  • Place under the nails is magnetized;
  • Not very big weight;
  • The sizes, optimum for roofing works.

Disadvantages:

  • The cost is very high.

Vira 900121

Vira 900121

Relatively simple externally hammer. His handle is made of metal, to facilitate its construction made hollow. The lower half of the handle is covered with rubber - this is done so that the palm of the tool does not slide off. For greater reliability, the creators hardened steel used here.This tool weighs no more than 600 grams, in connection with which the hand almost never gets tired while working at height.

As for the striker, it, as befits a roofing tool, incorporates a shock surface and a nail puller. With the help of Vira 900121, you can not only hammer in nails, but also align the edges of the roofing. But the most important thing is that they don’t ask for a lot of money for this product!

Advantages:

  • Made from hardened steel;
  • On the striker there is a nail puller;
  • The handle can boast a rubber coating;
  • Slight thickening at the end of the handle;
  • The optimal weight that will suit any roofer;
  • There is a magnet;
  • Not the biggest cost.

Disadvantages:

  • None.

What hammer to buy

1. KAPRIOL 12301 should be bought in case you need to proceed with the destruction of walls, old furniture and some other objects. This instrument has a three-kilogram mass and a 90-centimeter length. But its main advantage is in the fiberglass handle, which will not allow the sledge hammer to accidentally slip out of hand.

2. If it seems to you that 3 kg for a sledge hammer is not enough, then pay attention to FIT 45232. The weight of this tool has been increased to 4 kg. Of course, there are heavier sledgehammers, but their work is very quickly physically exhausting.

3. If we talk about traditional metal hammers, the most admirable is the Inforce 59035. The design of this tool is thought out to the smallest detail. Here, even a thickening at the end of the handle is, which, together with the grooves for the fingers, will not give the hammer the slightest chance of slipping. You definitely will not be disappointed in the acquisition of such a tool!

4. The twice heavier hammer is the Case of 315100. This is a tool from a domestic manufacturer, also equipped with a fiberglass handle. Many buyers liked not only its design, but also the low price tag.

5. Mason hammers cost a little more than usual. This is clearly seen in the example of BISON MASTER 2015-05_z01. This product can be recommended to those who still want to save. It has a wooden handle and a combined head made of steel 55.

6. Sturm 1010-05-600 is a bit better for a bricklayer. The weight of this tool is brought up to 600 grams, and on its handle there are notches in which the fingers of the worker are ideally placed. But this model is more expensive.

7. In the case of searches for a torqueless hammer, you can opt for SANTOOL 030833-675. This tool from the Israeli company has a 680 g mass and 32 centimeters long.

8. For body repair or similar purposes, choose Unipro 16148U. This is a leveling hammer offering two interchangeable nozzles. Its weight is 500 g.

9. Bahco 485 is best for roofing. This tool has not only a square impact surface, but also a nail puller. The high cost is due to the magnetized place under the nails and the maximum service life.

10. Vira 900121 shows quite a bit worse in roofing itself. This hammer also has a magnet, and there is a protrusion for leveling roofing materials. In this case, the purchase of the tool will take a little money.

It will be interesting to friends too

 

 

 


mylogo

Selection

Ratings