Initially, the sledgehammer was conceived as a blacksmith's tool, but then it became widespread in the construction, repair of machinery, plumbing. The large mass of the striker, which is gaining strength in the span, allows powerful blows without the use of electrical or pneumatic energy. Sledge hammer is divided by weight, where there are models from 1 to 8 kg. We have created a rating of the best sledgehammers for forging, tire fitting, sheet workpiece editing, fixing hardware fixing, breakdown of masonry and crushing materials, which will help to orient in the features of the tool and select the appropriate one.
Content:
The best sledgehammers weighing up to 2 kg
This is a small tool for driving reinforcement, forging small parts or disassembling various components of a car. Due to the small mass of such a device you can work with one or two hands.
Inforce 2000 59070 - with extra strong handle
This is the best sledgehammer for plumbing and other intensive activities that will withstand increased daily loads, thanks to a fiberglass handle. Glass fibers are resistant to mechanical shock and vibration, as well as to hanging temperature.
A mass of 2 kg is optimal for pushing heavy machine assemblies or leveling sheet metal. The handle has clear limiters both at the end and after the grip area, which eliminates slippage during intensive work.
Pros:
- the hole for fixation of the striker is sealed outside to eliminate exposure to ambient moisture and temperatures on the fixing part;
- at the end of the handle there is a hole on which you can attach a cord for hanging the instrument;
- rubber pads on both sides of the handle;
- it is convenient to take with two hands, and there is still room for removing the user's hands from the point of impact;
- the steel block does not crack;
- shock absorption;
- handle length 280 mm;
- long service life due to fiberglass not subject to rotting and cracking.
Minuses:
- cost from 680 rubles;
- because of the sealed hole, it is more difficult to control the quality of the fit and notice the first symptoms of the handle shift outward.
Sibrtech 2000 10918 - with forged head
This is the best sledge hammer weighing 2 kg, the striker of which is made of structural carbon steel with a forging head up to 30 mm in depth, which gives it sufficient strength to drive steel reinforcement, but at the same time allowed to have an average cost of 500 rubles.
The sides of the striker are smooth, which ensures a good fit when the tool touches the impact surface.
Pros:
- cushioning action due to fiberglass in the composition of the handle;
- an extension at the end of the handle that helps hold the tool with a strong span;
- rubber pads provide strong adhesion even with sweaty hands;
- hole for attaching the lace and hanging;
- 375 mm handle length is convenient for both short strokes when installing equipment, and for wide swing and holding with two hands;
- the rubber ring additionally protects the entry point of the handle into the metal part.
Minuses:
- there is no clearly defined limiter on the handle that prevents the movement of hands to the striker;
- It is difficult to control the density of the handle at the expense of the closed blind side at the top of the striker.
Top 5 kg sledge hammers
This is a more powerful tool that only works with two hands. It is used for breaking down thick wall masonry, hammering anchors, crutches for securing sleepers, and even as a sports projectile for pumping back muscles when hitting the rubber tire.
SANTOOL 5000 gr 030820-500 - good for dismantling
This is the best sledgehammer for demolition work due to the weight of 5 kg and a very convenient handle that allows you to hold the tool with two hands.The 900 mm handle length makes it possible for the user to be far from the point of departure of fragments and bricks falling out, which protects the feet from impact.
The 400 mm rubber part is practical for short strokes and firm holding during a wide swing.
Pros:
- fiberglass as the base material of the handle;
- the ability to control the strength of the nozzle of a metal element due to the protruding part of the handle on top;
- a large hole at the end for hanging the tool on a thick nail so that it does not occupy space on the floor;
- completely covered with rubber part of the handle, providing a strong hold;
- fixing striker with special reliability;
- tapering form of grip, convenient for grip with any size of palms.
Minuses:
- cost from 1600 rubles;
- there is no limiter at the end of the handle;
- due to the large mass and length it is more difficult to transport.
VIRA 5000 g 900250 - for clogging fasteners
This is the best sledge hammer for hammering large fasteners, especially in hard-to-reach places, since the 100 mm of the handle coming out of the striker are protected by a thick rubber shell. This allows you to purposefully beat with maximum force without fear of damaging the handle on the protruding rim.
The diameter of the hand grip part is kept thin throughout the entire shaft, which is convenient for both sweeping strokes and for tapping lightly with wide-spread hands.
Pros:
- fiberglass is resistant to high temperatures and rotting, and does not swell;
- 910 mm length allows you to make a wide swing and beat with great force;
- at the end there is a stopper that protects the instrument from departure;
- thick rubber clutch before striker;
- durable operation;
- bright rubberized coating, thanks to which a sledgehammer can be immediately found on the rack.
Minuses:
- cost from 2150 rubles;
- there is no stopper on the handle between the girth part and the rest;
- the total weight is more than 6 kg, which is inconvenient during transportation.
The best sledge hammers weighing from 7 kg
Such a tool is used for blacksmithing or solid reinforcement. It is convenient to work on it and as on a small anvil on which something can be tapped with a hammer. To use such a sledgehammer requires good physical preparation.
Sledgehammer 7000g Pavlovo 10965 - for smithy
This is the best sledgehammer to work in the forge due to its mass of 7 kg and the presence of selective hardening of the hammer Its surface is covered with anticorrosive paint, and the handle is completely wooden, which prevents it from melting when in contact with hot objects.
The main part is made of steel St40-60. The handle is well dried and has a moisture index of not more than 12%. The hardness of the impact part is 48-52 HRC.
Pros:
- you can monitor the quality of landing due to the open part of the striker;
- 700 mm handle length is optimal for hard shots;
- polished handle with ergonomic notches, tapering from the end;
- Bt-577 anti-corrosion coating will keep metal for a long time.
Minuses:
- cost from 1350 rubles;
- no rubber linings;
- there are no anti-slip restraints;
- very simple design.
It will be interesting to friends too
