Chisels have an oblong rod, which can be square, rectangular, oval, hexagonal or round. One of the edges is sharpened from two sides and is the working part. The opposite end is designed for striking and is called the butt pad. The tool is used in forging and plumbing, as well as in various repairs of the premises. Our ranking of the best chisels shows popular models for manual use and in combination with pneumatic power tools, which will help you choose a device for cutting materials, cutting shapes in metal and stone, and metalworking work on disassembling rusted joints.
The best hand chisels
This is a metalworking tool, through which you can cut the grooves in the metal, unscrew the old nut, disassemble the compressed equipment.
Sculptors apply them to fine work on shaping their works. On construction and repair with their help, you can perform a small dismantling of masonry or remove the finish layer. When choosing the most important mass and width of the working part, as well as security for the hands of a specialist.
FIT 46722 - a modern and affordable option
This is the best hand chisel with a modern design, which costs from 120 rubles. The core has a hexagonal shape and is made of tool steel.
Its length of 250 mm allows the sting to be instructed on the elements located below the surface and also to work on a fracture when dismantling brick structures.
A thick rubber handle with longitudinal edges helps to hold the tool firmly and reduces recoil when hit with a hammer.
Pros:
- the width of the working part of 22 mm helps to make a groove for the wire in one pass;
- optimum length of 250 mm for access to deepenings and work as the lever;
- a thick rubber handle that reduces vibration;
- the hot edge of the sting lengthens the time it takes to grind;
- hexagonal rod with a diameter of 16 mm is difficult to bend;
- mushroom-shaped backplate protection to prevent a blow to the hand when missed;
- blue paint to improve appearance.
Minuses:
- weight of 450 grams can tire the hand with prolonged use;
- on solid steels, the sting is jammed, which is corrected by repeated quenching and sharpening.
TOPEX 03A149 - for large recesses
This stylish chisel from Topex is the best for working on large recesses or between interfering parts of equipment, when you need to reach the area behind them, because the tool length is 400 mm.
Such parameters also help with thick masonry for cutting down the technological window with access to communications or laying ventilation.
Pros:
- attractive price of 200 rubles;
- hexagonal rod having stiffening ribs, preventing its deformation under loads;
- stylish bright yellow handle with a logo;
- wide fungus to protect hands from being hit by a hammer;
- four wavy cutouts on the handle for repeating the form of clamping with your fingers and a stronger grip;
- 19 mm working part width is optimal for most types of plumbing and construction manipulations.
Minuses:
- the handle with the fungus is constantly moving along the rod, so it must be reinstalled on glue or foam;
- to the length of the chisel 400 mm you need to get used to after a short rod;
- weight is 870 grams.
Stanley FatMax 25x305 mm - for all types of metal
This is the best manual chisel for the cutting of brass, steel, aluminum, stainless steel, copper and cast iron, because it has a special hardening and subsequent release.
The working part of 25 mm allows you to cut the thick bolts from one stop without moving. With this indicator, it is convenient to cut the grooves in the metal and grooves in the walls.
The length of 305 mm is optimal for retention and accurate guidance during intensive work, as well as manipulation in narrow places.
Pros:
- hexagonal rod is durable and resistant to bends;
- diameter of the main part of 20 mm allows you to freely use the tool as a lever for removal of the combined parts from each other;
- powder coating metal;
- shaped rubber handle with a thickening in the center for ergonomic grip;
- increase the diameter of the rubber grip at the end to prevent the hand from slipping;
- fungus for protection against impact;
- working part width 25 mm;
- stylish bright design, so that you can immediately see where the tool is (practical, if lost).
Minuses:
- cost from 700 rubles;
- weight more than 1 kg.
The best chisels for perforators
Such models of chisels are used to insert an electric or pneumatic perforator into the cartridge.
The shank of the rod is equipped with special grooves for gripping the fastener in the cartridge, therefore the type of fixation, along with the width and length of the working part, are the main selection criteria.
SDS MAX MATRIX 70343 18x25x600 mm - for laying communications
This is the best chisel for a punch, which is used for the purpose of laying communications. For mounting in the chuck, SDS-max grooves are provided. Work is carried out in a blow mode without rotation.
With it, it is easy to punch holes for ventilation in the bearing walls, after drilling with a drill, because the length of the rod is 600 mm.
Work with such a chisel can be carried out only on the one hand, which is practical when the floor is high or in the cold season.
Pros:
- rod diameter 18 mm has sufficient rigidity and resistance to deformation;
- 25 mm cutting edge width allows you to confidently enter the joints between the bricks and effectively separate the materials from each other;
- special type of alloy steel, resistant to corrosion;
- length 600 mm suitable for the largest masonry width;
- hardening sting followed by tempering;
- long service life.
Minuses:
- cost from 400 rubles;
- the type of fastening of the shank SDS-max is less common on punchers, so you need to choose the appropriate model of the tool;
- weights the total weight of the punch per 1 kg;
- length 600 mm is difficult to put in a briefcase with a perforator, so you have to be transported separately;
- Chisel free travel in the chuck can reach 2 cm.
MATRIX 70311 (40x400 mm) - for disassembling walls
This is a good chisel to interact with the hammer drill when dismantling the masonry or removing the finish, because the blade width is 40 mm, which allows you to lift a significant layer (2-3 times more than other models) in one pass.
The length of 400 mm is optimal both for work on the surface, which does not turn out to be very bulky, and for penetration with thick masonry.
Pros:
- type of attachment to the cartridge SDS-plus is more common;
- Made of 40X alloy steel;
- good blade sharpening angle for cutting the surface layer and deepening;
- cutting edge width 40 mm;
- cost from 280 rubles;
- anti-corrosion composition;
- Suitable for all types of stone.
Minuses:
- weight punch immediately to 460 grams, which can be felt during prolonged operation.
It will be interesting to friends too
