9 best hacksaws

How does a quality handsaw differ from a bad one? Perhaps the metal from which its main part is made. A bad saw has almost no sharpened teeth. And even if they seem to be sharp, then they cease to be already after one or two works. A good hacksaw has a steel that does not rust, and holds its sharpness for a long time. In this material we tried to tell about the best hacksaws - there are no any serious complaints about these tools. And the discussion will deal only with manual models, since Vyroved has already talked about electroslabs.

Manual hacksaw which company to choose

Production of hand tools employed a huge number of companies. There must be at least a couple of similar enterprises in each country. And only a few companies were able to go global. This is not to say that they have been successful due to the quality of their products. No, it all depended on luck and marketing. So do not think that high-quality hacksaws produce only those companies whose name is known. However, let's not seriously develop this topic.

If you do not trust obscure firms, then pay attention to products under the following brands:

1. Encor

2. ISTAL

3. VIRA

4. STANLEY

5. Fit

Usually products under these trademarks do not cause any complaints. And do not worry that some of the listed brands are domestic.

The best hacksaws for wood

ENKOR 9858

Hacksaw, belonging to the series "Wolf", as evidenced by the inscription on its working part. The tool has a plastic handle, which has a rubber pad. The hacksaw is designed for cutting wood. To do this, it is equipped with a set of teeth with a height of 4.5 mm. Each tooth is sharpened at three angles, which significantly speeds up the cut.

The length of the tool can be called slightly shortened - it is 400 mm. The handle is screwed on three screws, which allows you to not doubt its reliability. The canvas is made of high strength steel. The tool comes complete with a plastic case, which plays a protective role during transportation.

Advantages:

• The teeth ground at three corners;
• The handle is securely bolted to the canvas;
• The canvas is polished;
• On the handle there is a rubber pad;
• Comes with a plastic case;
• Teeth hardened;
• Low price.

Disadvantages:

• None.

ENKOR 9857

Another joiner hacksaw from a famous Russian manufacturer. But it belongs to the family "Beaver" - the corresponding inscription can again be found on the canvas. As in the case of the "Wolf", the fastening system to the handle consists of three screws. There is also a rubber pad, which reduces the load on the palm. At rest, the hacksaw must be in the plastic case supplied in the kit.

The canvas of this product is made of polished and high-strength steel. The teeth are universal - they are sharpened only at two angles. As for the handle, it allows you to outline the angles of 45 ° and 90 °, without using any auxiliary tools. A distinctive feature of the ENKOR 9857 hacksaw is the length increased to 500 mm.

Advantages:

• Divorced and very sharp teeth;
• There is a plastic cover;
• Low cost;
• Length increased to 50 cm;
• The handle is securely attached to the canvas;
• There is a rubber pad.

Disadvantages:

• Teeth not hardened;
• The teeth are sharpened only from two sides.

IZHSTAL 030108-050

The 500 mm joiner's saw, made in Izhevsk, is notable for its low cost. This is one of the cheapest hacksaws among those that possess double-sided sharpening of teeth. However, you will have to accept the fact that the teeth are not divorced here, which will definitely affect the speed of cutting wood. If you are doing this extremely rarely, then IZHSTAL hacksaw 030108-050 will be a profitable investment. If you are cutting something regularly, it is better to consider the tool more expensive.

The handle of this model is made of orange plastic. It is attached to the canvas with three bolts. As for the teeth, their pitch is 6.5 mm. The size of the teeth can be called average. Unfortunately, the handle does not have any additional functions - with its help you will not draw off the corners.

Advantages:

• Reliable fastening of the handle to the canvas;
• There is a rubberized part;
• Very low price tag;
• 500 mm length.

Disadvantages:

• Only double-sided sharpening;
• The tooth is straight;
• The teeth are not hardened.

The best hacksaws on aerated concrete

ENCOR 19183

A hacksaw from the company ENKOR, belonging to the family "Fox". It differs from other tools with a small tooth, the height of which does not exceed 2.5 mm. The teeth are hardened, indicating their long service life. The manufacturer recommends using this hacksaw to cut products from aerated concrete. The length of this model is 500 mm - an ideal parameter.

As in the case of the above hacksaws, the canvas here is attached to the handle with the help of three screws. This is the most reliable system - to break the tool accidentally fail. The handle was made of yellow plastic. Most of it is covered with rubber, thanks to which you can work with this saw without gloves.

Advantages:

• On the handle there is a rubber coating;
• Hardened teeth;
• Copes well with aerated concrete;
• Optimal length;
• The handle is securely attached to the canvas;
• Used quality steel.

Disadvantages:

• High price.

ENCOR 9847

This saw even looks very different from its competitors. Here, a carbide plate is used as a web. It is located on her teeth, having a very large size. Such a hacksaw turned out to be heavier than a steel counterpart. But on the other hand, it copes with the cutting of aerated concrete and products made from other abrasive materials without any problems.

On the handle of the hacksaw from the series "Raven" can not say something special. It was created from yellow plastic, which is customary for products from the company ENKOR. Part of the handle is covered with a rubber lining that allows you to work without gloves. It is attached to the canvas with the help of a traditional system consisting of three screws.

Advantages:

• There is a rubber pad;
• Reliable fastening of a cloth to the handle;
• The canvas was created from hard metal;
• Serves very long;
• Perfectly copes with cutting abrasive materials.

Disadvantages:

• The hacksaw will seem very expensive to many people.

The best hacksaws

VIRA 801010

Externally simple hacksaw for metal cutting. Its handle was created from two components. The main one is plastic. The second component is a rubber pad, thanks to which the palms almost never get tired, as well as they do not appear corns. As for the other parts of the hacksaw, they are made from tool steel. The cloth used here is standard - 300 mm long, it can always be replaced.

Advantages:

• Traditional linen sold in every store;
• On the handle there is a rubber pad;
• Easy web replacement;
• Reliable fastening of the handle to the main part;
• Afford almost everyone.

Disadvantages:

• Someone complete canvas seem sharp enough.

YATO YT-3161

Nice externally metalwork hacksaw. Uses traditional 300mm canvas.The included canvas belongs to the 24TPI type. It should be noted very easy to replace it - auxiliary tools are not required. Also, buyers praise this product for the ergonomic handle. It is equipped with a large layer of rubber, so that the palm remains in order even after several hours of work.

Advantages:

• On the handle there is an overlay from qualitative rubber;
• Reliable design;
• Fast replacement of a cloth;
• The included canvas is of high quality;
• The optimum length for working with metal.

Disadvantages:

• The cost is clearly too high.

STANLEY Mini 0-20-807

Sometimes a worker needs to cut the metal part in a hard-to-reach place. Or he needs to cut a very small piece of metal. For all these purposes, the traditional metal saw is not suitable - something less is needed. This something is STANLEY Mini 0-20-807. This hacksaw was very miniature. In fact, it is made in the form of an ordinary knife, but with some reinforcement - otherwise the design would quickly collapse.

The product uses a 300-mm canvas, 50 mm of which are hidden in the handle. The handle is single element - it was created from plastic by injection molding. There is an adjustment of the length of the retractable canvas. All this allows you to cut "flush" with the surface. Interestingly, theoretically a hacksaw allows even broken blades to be used.

Advantages:

• Unique miniature design;
• Broken blades can be inserted;
• Work in the constrained conditions is possible;
• Minimum cost;
• Standard webs are used;
• It's hard to break.

Disadvantages:

• The handle is not rubberized;
• Not suitable for cutting large amounts of metal.

Best drywall saw

STANLEY Fatmax 0-20-556

Very small hacksaw. Most of all, it resembles an ordinary knife. The difference lies only in the presence of teeth. The tool length is 302 mm. The handle is rubberized, so that the palm on it practically does not slip. In general, this is the best option for processing drywall - such a hacksaw leaves behind a clean cut.

Advantages:

• The canvas is made of durable metal;
• Very good cutting drywall;
• Rubberized grip;
• High reliability;
• Minimum weight;
• Compact size.

Disadvantages:

• The price can hardly be called low.

What kind of manual hacksaw to buy

1. If you are engaged in carpentry business, then you should consider the option of buying ENKOR 9858. This hacksaw has hardened teeth, sharpened on three sides. The cloth is bolted to the handle with the help of three screws - this design is the most reliable.

2. A little more simple saw is ENKOR 9857. This tool also copes well with any types of wood, but the process in this case will go slower, as the teeth are sharpened only from two sides. But this hacksaw is 100 mm longer.

3. Even cheaper product is ISTAL 030108-050. This is the best option for those who need a hacksaw once a year or even less. Then you will definitely not regret your savings.

4. For sawing aerated concrete, you should use the ENKOR 19183 hacksaw. Its cost is quite high, but it does not have any serious flaws. In this case, a small tooth is used, which should have a positive impact on the accuracy of work.

5. Even better, the gas concrete is handled by ENKOR 9847. But this hacksaw, due to the materials used here, is much more expensive. It should be bought only in the case of subsequent regular use of the tool.

6. For working with metal, you can purchase VIRA 801010 and YATO YT-3161. These hacksaws are about the same. They have rubber inserts, their canvases are easy to change, and the cost of tools does not cause fright (although the latter model applies to a lesser extent).

7. If there is little space for metal cutting, then STANLEY Mini 0-20-807 comes to the rescue. This is a miniature tool that is not larger than any knife. At the same time they support the standard 300-mm canvas.

8. If you regularly work with plasterboard, then we recommend that you purchase STANLEY Fatmax 0-20-556. This is a narrow tool with sufficiently large teeth, which is sawed with a clean cut.