Polypropylene pipes are much lighter than steel pipes and better tolerate exposure to moisture and moisture from the outside, not being susceptible to corrosion. This allows them to be widely used for laying plumbing and heating inside the building, underground and on the surface. The rating of the best soldering irons for pipes will show the models tested by users, distinguished by reliability, functionality and various shapes, which will help to choose a model for installation in different conditions.
The best X-shaped soldering irons for pipes
This type of tool has one or two heating elements located in a flat platform. It resembles the sole of an iron or a thick sword. It drilled holes from 1 to 3, in which are installed the couplings of different diameter for the soldering of pipes.
The number of holes and the power of the soldering iron affect the speed of work and the ability to simultaneously connect complex joints with several sizes of diameters.
Inforce 03-12-02 - for home and part-time work
This is the best soldering iron for plastic pipes, well suited for repairs in the apartment and periodic part-time work.
The device is equipped with two heating elements, the inclusion of which is regulated by toggle switches on the case. Depending on the combination, the soldering iron can work with a power of 700, 1000 or 1700 watts. This affects the rate of heating of the iron when working with plastic of different density.
Pros:
- comfortable rubber grip;
- three holes on the sword for combining tips and soldering access close to a wall or floor;
- it is completed with nippers for cutting of pipes, gloves and a tape measure;
- there is a roomy case where everything you need is placed, including attachments;
- stand for work on the table has a cruciform shape and an additional clamp to secure it in a vertical position;
- turning on the tumbler is highlighted by a diode, so you can immediately see how much power is set at the moment;
- comes with six nozzles with a diameter of 20 to 63 mm;
- gains temperature quickly and it is mechanically regulated in the range from 50 to 300 degrees;
- when heated, the indicator goes out, indicating that the operating temperature has been reached.
Minuses:
- scissors and tape measure in a set of poor quality - enough for a couple of times, and then have to be replaced;
- the case is not durable - it can open accidentally when moving a tool to an object;
- when first turned on it smells like burnt plastic;
- nozzles when shipped from the store are not wrapped in protective packaging and scratched.
Gigant GPW-1000 - for small tasks
Such a soldering iron for pipes is the best to independently dissolve communications for watering the kitchen garden or to establish another sampling point in the house. This is a simple model with a power of 1000 W, which will gradually heat up - it will not work for 100 joints per day, but it is quite possible to connect a dozen fittings with high quality. Its low price additionally attracts attention, helping to do everything yourself and save on the services of a master.
Pros:
- simple, intuitive control with two diodes, indicating temperature, and a regulator;
- cost from 900 rubles;
- securely insulated handle;
- Lightweight 1.25 kg and a short length will help to perform the soldering of pipes in place under the ceiling;
- There are six nozzles with a diameter of 20-63 mm;
- temperature is adjustable from 0 to 300 degrees;
- holes are provided on the base to, if necessary, secure the platform on a table or chair for stationary use;
- two sockets for combination coupling installation.
Minuses:
- the stand is made of tin - flimsy and wobbly;
- nozzles cover quickly;
- life is difficult to predict: some users work for several years, while others burn a heating element after the second joint;
- dangles at the insertion point of the soldering iron in the bracket.
PATRIOT PW 205 - one of the most powerful
Such a tool is useful for craftsmen engaged in professional installation of heating and plumbing. The soldering iron for pipes is the best in that it has a power of 2000 W, providing fast plastic heating and high performance.
The device is completed with a large case in which the carrying and extras fit. Thanks to the thick rubber handle, it is convenient to hold the soldering iron when connecting the pipes locally.
Pros:
- it is completed with 6 nozzles of different diameter;
- there are plastic pipe scissors and a screwdriver to quickly fix the clutches on the iron;
- two heating elements are switched on individually or together, which stepwise controls the heating rate;
- high-quality thermostat for smooth installation of the exact temperature;
- light weight 1.25 kg is convenient for work on your head;
- quickly gains operating temperature;
- differs in long service life at daily use;
- gloves from the set reliably protect against burns.
Minuses:
- a short power cable with a length of 2 m will always need to be carried when soldering pipes in place;
- very thin metal on the body - it bends easily and rattles;
- clutches often unwind, even if they are well tightened;
- the nozzle with a diameter of 63 mm does not fit into the last hole — it rests against the bracket;
- scissors quickly break - literally after ten cuts of a pipe with a diameter of 40 mm;
- a weak handle - it will not work with a soldering iron on the pipes, otherwise it will bend;
- the stand is flimsy and unstable;
- paint burns out in the place of fixing the heating element to the body.
Top tube soldering iron
The power tool of this type is characterized by the presence of a heating element in the form of a long cylinder.
The location of the pipe dies on it is unlimited - they can be fixed at the very base or on the edge, which makes soldering easier in hard-to-reach places (niches in the toilet, under the bathroom, under the floor and near the ceiling). Their power varies from 800 to 2000 W, affecting only the heating rate.
STURM TW7218 is a good choice for a professional.
This is the best cylindrical soldering iron for pipes from the German manufacturer to dock fitting and plastic communications in narrow places and close to the wall.
On the heating element it is possible to install three pairs of nozzles at once, in order to quickly heat pipes of different diameters and create complex transitions and connections. A power of 1800 W contributes to accelerated heating and reaching the operating temperature.
Pros:
- small weight of 1.1 kg is practical for long-term manual welding of polypropylene pipes;
- there is a plate resting against the body and serving as a stand for stationary use of a soldering iron;
- a knob at the back of the handle helps set the right temperature;
- two LEDs indicate the current status of the device;
- it is completed with a metal case, nozzles and a six-sided key for installation of couplings;
- compact dimensions to get and solder in narrow places.
Minuses:
- only 4 nozzles are included (16-32 mm) - for other pipe diameters it will be necessary to buy more;
- the readings of the thermostat do not correspond to reality - you need to calibrate yourself on the instrument and remember the switch position on the desired values;
- the stand is unstable and the device can easily roll over if you accidentally hook on the wire with your foot;
- nozzles are knocked together during transportation and the coating deteriorates.
Elitech SPT 1000 - make a decision in the bath
It is a worthy soldering iron for pipes from a Russian manufacturer, suitable for laying pipes in a constructed bath and other small rooms. Due to its compactness, it is best for soldering close to walls, in niches or under the floor.
The handle is equipped with ergonomic cutouts for fingers, which is very convenient for manual mode. The stand allows you to use it on the table and hold the pipes with two hands.
Pros:
- high-quality installation of the cable into the case has a thick insert that prevents the wire from rezamyvaniyu in a strategic place;
- fits well in the hand;
- attractive price from 2000 rubles;
- Some users work 6 years and do not break.
Minuses:
- the thermostat in the back of the handle clings to clothing and can change position - the device will become warm badly or burn the fitting;
- weighs 2.65 kg, which is heavier than analogs and will tire hands more quickly;
- short cord 2 m;
- in the case almost nothing fits in the extras;
- there are no temperature markings on the thermostat - all settings are on the eye;
- Included maximum nozzle has a diameter of 32 mm.
It will be interesting to friends too
